Difference between revisions of "Mark2 Assembly"

From Aus3D Wiki
Jump to navigation Jump to search
Line 376: Line 376:


=== Filament Gear ===
=== Filament Gear ===
Requires:
* {{Qty|1|MK7 Filament Gear}}
Slide the filament gear onto the motor shaft, with the drive section nearer the motor as shown. Line the filament channel up with the PTFE tubing, and fix the gear in place. Make sure to align the gear's grub screw with the ground flat on the motor shaft - this will ensure a stronger grip.
=== Idler Arm ===
=== Idler Arm ===



Revision as of 12:09, 14 December 2015


Mark2 3D Printer


Mark2BigPreview.png

Getting Started

A sharp knife can make it easier to pry up the edges of the paper - but take care not to scratch the acrylic.

First things first - thanks for your support! We appreciate your business, and hope that your experience with our printer is a happy and productive one! If you get stuck, and you can't find the answer you need here, feel free to contact us - we'd be happy to help!

General Notes

Here are a few important notes before we proceed with assembly.

Our acrylic frame is as sturdy as they come, but over-tightened screws can still cause damage. Spring washers significantly reduce the chance of damage, and ensure that bolts stay tight long after assembly. Be sure to use one of the included spring-washers on every bolt that comes into contact with the acrylic frame.

Test all linear bearings before using them by running them along one of the included smooth rods - sometimes they have too much grease applied internally, which can make them resistant at first. If this is the case, rinse the bearing under water briefly, dry as best as possible, and try running along the smooth rod again. Over time the grease will spread through the bearing, making them smoother - running the bearing along the rod a few times may help. Generally, after rinsing and some motion, the bearings should be smooth enough to move under gravity when the rod is held vertically.

Many of the images in this guide are animated - click on them to see the animation.

Let's Go!

To get started, find yourself a nice, open space to work - a table or workbench is ideal. Open up your kit, and grab all of the included parts out and arrange them nearby. After unboxing everything, take the time to compare the bill-of-materials (BOM) against the contents of the kit. We work hard to make sure everything you need is in the box, but it's good to double check. Many components come inside one of the labelled boxes - if you're having trouble finding a part, check the BOM to find out which box it should be in.

Once you've got that sorted, it's time to get the acrylic parts ready. You'll want to peel the protective paper coating off of the acrylic before putting the printer together. Using a sharp knife or fine pair of tweezers can make it easier to separate the paper from the acrylic. This can take a little while - whether you want to do it all in one go, or bit-by-bit as you assemble the printer is up to you.

Main Frame Assembly

Z Motor Brackets

Z Bracket Assembly

Requires:

  • 4x z-motor-brace
  • 2x z-motor-bracket
  • 4x M3x20mm Bolt
  • 4x M3 Spring Washer
  • 4x M3 Hex Nut

Assemble both Z Motor Brackets as shown in the images.

Side Panels

Z Bracket Installation

Requires:

  • 2x Assembled Z Bracket
  • 4x M3x20mm Bolt
  • 4x M3 Spring Washer
  • 4x M3 Hex Nut

Install the brackets onto the side panels. Take note that the side panel with the mounting holes for the controller goes on the left, and the panel with the mounting holes for the PSU on the right.

Horizontal Panels

Horizontal Panels Installation

Requires:

  • 2x Assembled Side Panel
  • 1x y-axis-front
  • 1x y-axis-rear
  • 1x frame-top-bar-front
  • 1x frame-top-bar-rear
  • 1x horizontal-brace
  • 14x M3x20mm Bolt
  • 14x M3 Spring Washer
  • 14x M3 Hex Nut

Insert the five horizontal panels into the slots on one of the side panels. It may be helpful to lay the side panel flat so everything stays in place.

Correct orientation of panels

Take care in the orientation of the y-axis-front and y-axis-rear panels - they are not symmetrical. When viewed from the front, the y-axis-front panel should have a notch on the right-most screw hole (pictured below). The y-axis-rear panel should have the rectangular endstop cutouts to the left.

One of the z-top-panels has a cutout for wiring - this panel should be placed nearer the back of the printer, behind the other z-top-panel. If you're using the LCD add-on, swap the front-most z-top-panel out for the LCD cutout. The rear panel should have a cut-out for running cables to the LCD.

Flip Printer on side for easier assembly

Place the remaining side panel on top of the horizontal panels, and fasten it in place. There are seven bolts to install on each side. Once done, flip the frame over (taking care to hold everything together) and fasten the other side panel in place.

Y Axis

Bed Support Plate

40px-Ambox warning yellow.svg.png Caution:If you are building a printer with the build volume upgrade, you will have received a separate, enlarged bed support plate in the upgrade kit. For this section, please use the larger bed support plate instead of the default one.

Bearings

Bed Support Plate
Bearings Installed

Requires:

  • 4x LM8UU Linear Bearings
  • 8x Cable Ties
  • 1x Bed Support Plate

Orient the bed support plate as shown - take note of the position of the four holes on each side of the plate, they should match the image. It is possible to build the bed plate upside down - that doesn't work too well, so double check the orientation before starting.

Sit the linear bearings in the cutouts on the bed support plate, and cable tie the bearings in place. Run one of the smooth rods through both sets of bearings to ensure that they are correctly aligned, and ensure the cable ties are fully tightened.

If the rod seems to get stuck in the bearing before pushing through all the way, do not force it through - this will likely damage the bearing. Gently withdraw the rod, and try again slowly - sometimes when inserting the rod the recirculating balls inside the bearing can get jammed, and forcing them can cause them to dislodge from the bearing.

Trim away the excess cable tie lengths.

Endstop Trigger

Y Endstop Trigger Bolt (Above)
Y Endstop Trigger Bolt (Below)

Requires:

  • 1x M3x20mm Bolt
  • 1x M3 Spring Washer
  • 2x M3 Hex Nut

The Y endstop is positioned underneath the bed assembly. In order to actuate it, a bolt protrudes from the bottom of the support plate and makes contact with the switch. The position of the bolt can be changed to achieve different trigger points, which may be handy if you ever modify the printer. Install the bolt as shown in the hole third from the edge - this will allow for ~205mm of travel. Make sure that the bolt doesn't protrude more than a few millimetres past the end of the nut - otherwise it could press against the heated bed.

Belt Clamp

Belt Clamps Installed (And Endstop Trigger Bolt)

Requires:

  • 2x Printed Y Belt Clamp
  • 4x M3x20mm Bolt
  • 1x M3x30mm Bolt
  • 4x M3 Spring Washer
  • 5x M3 Hex Nut

Select one of the printed belt clamps, and install the 30mm bolt and nut as shown. This clamp will be used to tighten the y-axis belt later. The other printed clamp does not need the bolt and nut installed - it only clamps the opposite end of the belt in place. Fasten both clamps to the bed support plate as shown, with the clamp featuring the nut and bolt nearer the front of the bed support plate (away from the endstop trigger bolt). For now, do not worry about tightening the bolts holding the clamps in place - they will need to be loosened and re-tightened later.

Y Motor

Bracket

Y Motor Mount
Y Motor Mount Installed

Requires:

  • 1x Y Motor Bracket
  • 1x M3x20mm Bolt
  • 1x M3 Spring Washer
  • 1x M3 Hex Nut

Fix the motor mount in place as shown. Ensure the orientation is correct - the bottom of the acrylic part should be flat, while the top should have an angled cut towards the mounting tab.

Motor

Y Motor Installed
Y Motor Installed

Requires:

  • 1x NEMA17 Motor
  • 2x M3x15mm Bolt
  • 2x M3 Spring Washer
  • 1x GT2 Pulley

Insert the GT2 pulley onto the motor shaft, positioned as shown, and tighten the grub screws to hold it in place. Ensure one of the grub screws is directly over the flat of the motor shaft, in order to have the best grip possible.

Attach the motor to the bracket in the orientation shown, with the connector facing downwards.

Y Endstop

Note: it may be easier to do these steps in reverse order (e.g. install the endstop onto the bracket, then install the bracket in place) as the bolts can be difficult to reach once the bracket is in place.

Bracket

Y Endstop Mount

Requires:

  • 1x Y Endstop Bracket
  • 1x M3x20mm Bolt
  • 1x M3 Spring Washer
  • 1x M3 Hex Nut

Fix the endstop bracket in place, ensuring that it points upwards as shown.

Endstop

Y Endstop Installed
Y Endstop Installed

Requires:

  • 1x PCB Endstop
  • 2x M3x10mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut
  • 4x 3mm Plastic Spacer

Mount the endstop to the bracket as shown. Use a plastic spacer on each side of the PCB.

Motor and Endstop Wiring

Y Idler

Assembly

Y Idler Assembly

Requires:

  • 1x Printed Y Idler
  • 2x 624ZZ Roller Bearing
  • 1x M4x20mm Bolt
  • 1x M4 Hex Nut

Assemble the Y Idler as shown. Ensure that the bearings can spin freely.

Installation

Y Idler Installed

Requires:

  • 1x Assembled Y Idler
  • 2x M3x20mm Bolt
  • 2x M3 Hex Nut
  • 2x M3 Spring Washer

Attach the Y Idler to the inside of the front Y panel as shown.

Install Y Axis

Rear Smoothrod Caps

Smoothrod Cap Installed
Both Rear Smoothrod Caps

Requires:

  • 2x Smoothrod Cap
  • 4x M3x20mm Bolt
  • 4x M3 Hex Nut
  • 4x M3 Spring Washer

Install the smoothrod caps onto the Y Rear Panel as shown. Ensure the caps sit as low (and hence as flush with the top of the Y Rear Panel piece) as possible.

Install Bed Support Plate

Smoothrods in Position
Support Plate on First Rod
Support Plate on First Rod

Requires:

  • 1x Assembled Y Bed Support Plate
  • 2x 8mm Smoothrod

Slide both of the smoothrods through the cutouts in the Y Front Panel as shown, and position the rods so that they are approximately centred in the cutouts.

Hold the assembled bed support plate in the middle of the printer, and slide one of the rods through one of the sets of bearings as shown. Once the smoothrod is through the bearings, push it back and guide it into the cutout on the Y Rear Panel. The smoothrod caps installed previously should prevent it from travelling any further. Repeat this process for the remaining rod.

Front Smoothrod Caps

Front Smoothrod Caps Installed

Requires:

  • 2x Smoothrod Cap
  • 4x M3x20mm Bolt
  • 4x M3 Hex Nut
  • 4x M3 Spring Washer

Install the front two smoothrod caps to fix the smoothrods in place. At this point, you should check that the bed support plate can slide back and forth along the rods smoothly - it should be easily moveable by hand. If not, double check the previous steps and try and identify the problem.

Ensure that the endstop is triggered by the actuating bolt when the bed is moved all the way to the back of the axis - there should be an audible click as the switch is triggered.

Y Belt

Cut a 70cm long length of belt.

Move the bed support plate all the way to the back of the axis. Gently turn the printer over onto its back for easier access to the area underneath the support plate. Ensure that the belt clamp pieces are only loosely attached to the bed support plate. Fix the belt screw cap onto the end of the 30mm bolt as shown.

Run the belt around the Y idler bearings as shown, with the teeth on the inside of the belt path.

Pull the belt through, and push it through the rectangular slot in the uppermost Y belt clamp. Run the belt around the rounded end of the belt screw cap, and then slide the belt between the Y belt clamp and the bed support plate (the belt clamp needs to be loose to do this). Pull the belt out so that the end of the belt visibly exits from underneath the belt clamp. Ensure that the belt is centred underneath the clamp, and then tighten the two bolts that secure the belt clamp to the bed support plate. Once tightened, the belt should be clamped between the belt clamp and the bed support plate.

Loosen the Y idler as shown - this will provide more room to tighten the belt later.

Take the opposite end of the belt and run it around the motor pulley. Continue to pull that end of the belt up, and run it through the remaining belt clamp piece. Follow a similar process to clamp the belt between the clamp and the bed support plate as shown - ensure that the belt is as taught as possible before clamping it in place.

Once the belt is securely fastened at both ends, it is time to ensure the belt is correctly centred and tightened. There are two ways to tighten the belt - by tightening the two screws that hold the Y idler in place (which we loosened before installing the belt) and by tightening the 30mm bolt in one of the belt clamp pieces. While the printer is in this orientation it is easier to access the 30mm bolt than usual, so let's do the majority of the tightening there. Turn the bolt clockwise to tighten the belt - ensure that the belt screw cap stays straight (you may need to hold it loosely). As the bolt is turned, the belt screw cap should move and pull the belt tighter. If not, it is possible that the bolt is biting into the belt screw cap - the bolt should fit loosely inside the cap, and only the force of the belt pulling the cap back should keep it fitted to the bolt. If the bolt appears to be biting into the cap, remove the cap, ensure that the bolt cavity is clear of plastic, and try again.

Once the belt is nearly fully tightened, the final tightening can be done by tightening the bolts on the Y idler. Turn the bolts to move the Y idler closer to the frame again - but it's a good idea to leave a bit of a gap for future adjustments.

Heated Bed

Wrap Wiring

Wires Spiral Wrapped

Cut a 40cm length from the provided spiral wire wrap. Use this spiral wrap around the wires connected to the heated bed as shown.

Attach to Support Plate

Bed Bolted Down

There are a few different ways to mount the heated bed - we have a recommended default configuration, but we'll take a moment to explain the different options.

Firstly, the bed can be mounted using either three-point or four-point mounting. Four-point (where a bolt is used in each corner of the bed) is more traditional and more common, and will likely result in the bed being more securely fixed in place (hence reduced wobble or vibrations). However, using four points can make it more difficult to get the bed flat, as it's possible to over-constrain (and hence bend or deform) the bed if the bolts are not applying an even and balanced pressure. Three-point mounting avoids these problems, but the bed may not be as securely fixed in place.

The bed support plate has mounting holes for both three and four point mounting - however using three-point mounting will require the bed to be rotated 180° from the default configuration, and this can complicate wiring. For simplicity we recommend four-point mounting, but the option is there if you wish to experiment.

Additionally, the way in which the bed can be fixed to the bed support plate can be varied. We recommend using springs to offset the heated bed from the support plate, and springs are included for this purpose. Supporting the heated bed on springs is a good idea because it provides some protection if the print head accidentally crashes into the bed surface - the bed will allow some downwards movement before things start to break. However, during very fast movements, the springs can cause the bed to vibrate or lag behind the motion of the Y axis slightly - this can cause minor print artifacts in external surfaces. This should not be a problem at the default or at most reasonable print speeds, but is something to be mindful of if experimenting with higher build speeds. In this case, we recommend swapping the springs out for plastic spacers - spare spacers are included in the kit for this purpose. Just remember to take extra care not to crash the HotEnd into the bed!

Due to the vibrations mentioned, it's possible for the bolts holding the bed in place to work themselves loose given enough time - we recommend using (and include) nyloc nuts to address this; once tightened they should not come loose easily.

With that in mind, fasten each corner of the bed in place as shown for the recommended configuration. Alternatively, configure the heated bed as you see fit.

Extruder Assembly (Single Extruder)

X Carriage

Front and Rear Pieces

Bearings In Place
Bearings In Place

Requires:

  • 1x X Carriage Front
  • 1x X Carriage Rear
  • 4x LM8UU Linear Bearings
  • 2x M3x30mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut
  • 6x M3 Plastic Spacer

Insert the LM8UU bearings into the cut-outs on the X Carriage Rear acrylic piece. Place the M3x30mm bolts through the top two screw holes, and use three spacers along each bolt to separate the two acrylic pieces, as shown.

Mounting Plate

Mounting Bracket Assembled

Requires:

  • 1x X Carriage Mount Plate
  • 2x X Carriage Brace
  • 2x M3x15mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut

Attach the two brace pieces to the mount plate as shown. Note the orientation of the mounting plate - the endstop trigger (small hammer) should be on the left.

Attach Mounting Plate

Mounting Bracket Attached

Requires:

  • 1x Assembled X Carriage Front + Rear
  • 1x Assembled Mounting Plate
  • 2x M3x30mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut

Attach the mounting plate assembly to the front and rear X carriage pieces assembled earlier. For the time being, only fasten them together using the two bolts located at the bottom of the X carriage brace pieces (as shown). The remaining two bolts that enter into the mounting plate will be installed once the entire carriage is fitted on the X axis.

Fan

Fan Installed
Fan Mounting Arrangement

Requires:

  • 1x Assembled X Carriage
  • 1x E3D 30mm Fan
  • 4x M3x20mm Bolt
  • 4x M3 Spring Washer
  • 4x M3 Hex Nut

Install the fan on the outside of the carriage as shown - the label on the fan should be facing inwards, nearer the body of the carriage.

HotEnd

E3D have detailed instructions for assembling both the Lite6 and V6 HotEnds available online. Follow the instructions they provide, but don't yet insert the PTFE tubing or power up the HotEnd. Leave the fan separate for the time being.

Prepare HotEnd

Preparing PTFE
PTFE Trimmed

Insert the PTFE tubing into the HotEnd, as far as it will go. Refer to the documentation for the V6 and Lite6 if you're unsure if the PTFE is fully inserted. Push the PTFE through the printed E3D cap piece, and through the central hole in the aluminium extruder block, as shown.

Compact the HotEnd, cap, and extruder block together, and trim the excess PTFE away. Leave approximately 10-20mm of PTFE sticking out beyond the extruder - we'll cut it much more precisely in a little while.

Position HotEnd

HotEnd In Position
HotEnd In Position
HotEnd Wires Routed

Remove the HotEnd and cap from the extruder base. Insert the HotEnd into the mounting bracket, using the circular groove to centre the HotEnd as shown. It should loosely stay in place.

Organise the HotEnd wiring at this point - route the wires around the fan and through the small cut-out in the mounting plate.

Extruder Base Block

Extruder Base Block Installed
Extruder Base Block Installed

Requires:

  • 1x Metal Extruder Base Block
  • 2x M3x10mm Bolt
  • 2x M3 Spring Washer

Position the base block on top of the acrylic mounting plate, and insert the HotEnd, printed cap and PTFE tubing into the base block (as done earlier to check the tubing length).

Fix the base block to the acrylic plate using the two 10mm bolts.

Motor

Extruder Motor Installed

Requires:

  • 1x NEMA 17 Stepper Motor
  • 2x M3x20mm Bolt

Attach the stepper motor to the base block as shown. Be sure to use the stepper motor provided with the extruder parts - it's a higher-torque motor than the others, in order to ensure smooth and reliable extrusion. The correct motor should be deeper than the others.

Print Fan

Print Fan Assembled
Print Fan Positioned

Requires:

  • 1x Printed Fan Mount
  • 1x 50mm Blower Fan
  • 4x M3x30mm Bolt
  • 4x M3 Spring Washer
  • 2x M3 Hex Nut

Attach the fan to the printed mount as shown, then position the assembled fan and mount on the back of the extruder carriage. Do not secure the fan in place by fastening the bolts yet - leave the fan resting loosely on the carriage for the time being.

PTFE

Marking PTFE Tubing
PTFE Tubing Cut
PTFE Tubing Cut

Requires:

  • 1x MK7 Filament Gear

Slide the filament gear onto the motor shaft - it's unlikely to slide down all the way, as it will be blocked by the PTFE tubing. We are now going to cut the PTFE tubing as close to the gear as possible (the closer the tubing, the easier it is to print flexible filaments).

Using a sharp pen or pencil, draw the outline of the gear on the tubing. Remove the gear, then use a sharp pair of scissors (or other suitable tool) to cut around that outline as shown. Cut the other side of the tubing as shown.

After cutting, the tubing may be crushed or deformed - if so, use something 2mm in diameter (for instance, the smaller hex key) to ensure the inside of the tubing is circular and not crushed.

Filament Gear

Requires:

  • 1x MK7 Filament Gear

Slide the filament gear onto the motor shaft, with the drive section nearer the motor as shown. Line the filament channel up with the PTFE tubing, and fix the gear in place. Make sure to align the gear's grub screw with the ground flat on the motor shaft - this will ensure a stronger grip.

Idler Arm

Z Probe

Z Probe Installed
Z Probe Installed

Requires:

  • 1x IR Z Probe
  • 2x M3 Plastic Spacers
  • 2x M3x10mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut

The Z Probe is designed to mount to the same hole pattern as is used by the 30mm HotEnd cooling fan. The recommended mounting location is on the opposite side of the X carriage from the fan, as shown. Alternatively, the probe can be mounted directly to the cooling fan if preferred - but the offset values in the firmware will need to be adjusted accordingly.

Wiring

  • Spiral wrap
  • Cable tie

Extruder Assembly (Dual Extruder)

X Carriage

HotEnd

E3D have detailed instructions for assembling both the Lite6 and V6 HotEnds available online. Follow the instructions they provide, but don't yet insert the PTFE tubing or power up the HotEnd. Leave the fan separate for the time being.

Extruder

Follow the same process as used for the single extruder, but flip the second extruder around to suit.

Fans

Z Probe

Requires:

  • 1x IR Z Probe
  • 2x M3 Plastic Spacers
  • 2x M3x10mm Bolt
  • 2x M3 Spring Washer
  • 2x M3 Hex Nut

The Z Probe is designed to mount to the same hole pattern as is used by the 30mm HotEnd cooling fan. The recommended mounting location is on top of the cooling fan on the right of the X carriage - in this orientation the cable will exit back towards the X carriage.

Wiring

  • Spiral wrap
  • Cable tie

X Axis

X Motor Assembly

Linear Bearing

X-Motor Bearing

Requires:

  • 1x Printed X-Motor Part
  • 1x LM8UU Linear Bearing

Insert the linear bearing as shown. It should be a firm fit - you may need to use a hammer to gently tap the bearing in place. If the bearing is slightly loose, it can be clamped in place using two bolts through the part as shown.

Carriage Nut

X-Motor Carriage Nut

Requires:

  • 4x M3x15mm Bolt
  • 1x Leadscrew Carriage Nut

Insert the carriage nut, and fasten it in place as shown. The bolts should bite into the plastic of the printed part quite firmly.

Rod Tighteners

X-Motor Rod Tighteners

Requires:

  • 2x M3x10mm Bolt
  • 2x M3 Hex Nut

There is a nut trap inside each of the cylindrical cut-outs for the smooth-rods. Insert a nut into each one, oriented so that a bolt can pass through it through the hole in the printed part. If the nut is incorrectly oriented, try tapping the part gently - if you're lucky, the nut should tend towards being correctly oriented. If you're unlucky, you might need to remove the nut and drop try to place it again. Once in the correct orientation, screw the bolt into (but not yet extending out of) the nut, as shown.

Motor Pulley

X-Motor Pulley

Requires:

  • 1x NEMA 17 Stepper Motor
  • 1x GT2 Pulley

Install the GT2 pulley onto the stepper motor shaft, spaced as shown. Take care that one of the grub screws aligns with the flat of the motor shaft to ensure a good grip.

Motor Installation

X-Motor Stepper Installation
X-Motor Pulley Alignment

Requires:

  • 1x NEMA 17 Stepper Motor
  • 3x M3x20mm Bolt

Fasten the stepper motor in place as shown. It is easier later to wire the motor with the cable connector oriented downwards. Check that the pulley aligns with the large rectangular cut-out for the belt as shown.

Endstop

X-Motor Endstop

Requires:

  • 1x PCB Endstop
  • 2x M3x15mm Bolt
  • 4x 3mm Plastic Spacer

Install the endstop as shown, taking care to orient it correctly.

X Idler Assembly

Linear Bearing and Carriage Nut

Requires:

  • 1x Printed X-Motor Part
  • 1x LM8UU Linear Bearing
  • 4x M3x15mm Bolt
  • 1x Leadscrew Carriage Nut

Repeat the same process as used for the X-Motor assembly.

X Carriage Installation

Z Axis

Z Motors

Requires:

  • 8x M3x15mm Bolt
  • 8x M3 Spring Washer
  • 2x NEMA17 Stepper Motors (34mm)
  • 2x 8mm Couplers

Fix the Z motors in place as shown. Attach a flex coupler to each motor, with the motor shaft entering the smaller size of each coupler. Tighten the outer bolt to clamp the coupler in place, and then tighten the centre grub screw to ensure a secure fit.

Installing X Axis

Position the assembled X axis over the Z motors as shown. Lower the smooth rods through the top of the frame, through the linear bearings in the X axis and into the cutouts in the Z motor brackets. You may need to adjust the spacing between the X motor and X idler ends in order for the rod to fit smoothly.

Spool Holder

Spool Holder

Requires:

  • 1x 8mm Smooth-rod
  • 2x Printed Spool Holder Adaptor

Press each end of the smooth-rod into the printed adaptors. Insert the assembly into the cut-out on the printer frame, as shown.

Additional Resources

  • Exploded view of entire printer
  • Exploded view of extruder assembly