Difference between revisions of "Mark2 BOM"

From Aus3D Wiki
Jump to navigation Jump to search
(→‎Main BOM: Make Rods own category)
(→‎Main BOM: M3 x20 CSK - Only 5 (or 6 in 4-point) needed total, change from 10pcs to 8pcs)
 
(10 intermediate revisions by the same user not shown)
Line 7: Line 7:
|Part
|Part
|Quantity
|Quantity
|-
|Acrylic
|Acrylic Frame (see separate BOM)
|1
|-
|-
|Control
|Control
Line 34: Line 30:
|Control
|Control
|IR Z Probe with cable
|IR Z Probe with cable
|1
|-
|Control
|LCD Controller (20x4) + SD Card Reader
|1
|-
|Control
|LCD Controller Cables
|2
|-
|Control
|LCD Controller Adaptor
|1
|-
|Control
|Machined Metal Knob
|1
|1
|-
|-
Line 42: Line 54:
|Electronics
|Electronics
|IEC13 Mains Lead (default Australian)
|IEC13 Mains Lead (default Australian)
|1
|-
|Electronics
|MK3 Aluminium Heated Bed + Wire, Thermistor
|1
|1
|-
|-
Line 56: Line 64:
|4
|4
|-
|-
|Electronics
|Wiring
|USB-A Cable 1.5m
|USB-A Cable 1.5m
|1
|1
|-
|-
|Electronics
|Wiring
|Mains Wiring Harness
|Mains Wiring Harness
|1
|1
|-
|-
|Electronics
|Wiring
|12V Wiring Harness
|12V Wiring Harness
|1
|1
|-
|-
|Electronics
|Wiring
|Spiral Wire Wrap
|Spiral Wire Wrap
|2 metres
|2 metres
|-
|-
|Electronics
|Wiring
|Cable Ties
|Cable Ties
|Pack
|Pack
|-
|-
|Electronics
|Wiring
|Cable Tie Mounts
|Cable Tie Mounts
|10
|10
Line 111: Line 119:
|5mm to 8mm Flex Coupler
|5mm to 8mm Flex Coupler
|2
|2
|-
|-
|Print Bed
|MK3 Aluminium Heated Bed + Wire, Thermistor
|1
|-
|Print Bed
|200x214mm Glass Plate
|1
|-
|Print Bed
|Wooden Insulator
|1
|-
|Print Bed
|A4 Black Paper
|1
|-
|-
|Fixings
|Fixings
Line 118: Line 143:
|Fixings
|Fixings
|{{Bolt|M3|15}}
|{{Bolt|M3|15}}
|25
|30
|-
|-
|Fixings
|Fixings
|{{Bolt|M3|20}}
|{{Bolt|M3|20}}
|80
|85
|-
|-
|Fixings
|Fixings
|{{Bolt|M3|20|Countersunk Bolt}}
|{{Bolt|M3|20|Countersunk Bolt}}
|10
|8
|-
|Fixings
|{{Bolt|M3|30}}
|4
|-
|-
|Fixings
|Fixings
|{{Nut|M3}}
|{{Nut|M3}}
|120
|125
|-
|-
|Fixings
|Fixings
|{{Washer}}
|{{Washer}}
|120
|125
|-
|-
|Fixings
|Fixings
Line 151: Line 180:
|{{Nut|M4}}
|{{Nut|M4}}
|5
|5
|-
|Fixings
|Binder Clip (25mm)
|4
|-
|-
|Fixings
|Fixings
Line 157: Line 190:
|-
|-
|Misc
|Misc
|Kapton Tape 50mm Roll
|Filament Sample
|1
|1
|-
|-
|Misc
|Acrylic
|Filament Sample
|Acrylic Frame (see separate BOM)
|1
|1
|-
|-
Line 167: Line 200:
|Printed Frame Parts (see separate BOM)
|Printed Frame Parts (see separate BOM)
|1 Set
|1 Set
|-
|}
|}


Line 225: Line 257:
|10
|10
|1
|1
|[[File:Mark2-acrylic-FrameTopBarFront.PNG|frameless|250px]]
|[[File:Mark2-acrylic-FrameTopBarLCD.PNG|frameless|250px]]
|-
|-
|Top Bar (Rear)
|Top Bar (Rear)
Line 278: Line 310:
|1
|1
|[[File:mark2-printed-belt-screw-cap.PNG|frameless|200px]]
|[[File:mark2-printed-belt-screw-cap.PNG|frameless|200px]]
|-
|E3D-Cap
|1*
|[[File:mark2-printed-e3d-cap.PNG|frameless|200px]]
|-
|-
|Spool-Rod-Adaptor
|Spool-Rod-Adaptor
Line 300: Line 328:
|-
|-
|}
|}
<nowiki>*</nowiki> One per extruder / HotEnd, included separately in extruder pack.


== Single Extruder BOM ==
== Single Extruder BOM ==
Line 358: Line 385:
|Fixings
|Fixings
|Spring
|Spring
|1
|-
|Fixings
|Printed Circlip
|1
|1
|-
|-
Line 411: Line 442:
|Quantity
|Quantity
|Image
|Image
|}
== LCD Controller BOM ==
{| class="wikitable"
|Category
|Part
|Quantity
|Image
|-
|Acrylic
|Replacement Frame Top-Bar with LCD Cutout
|1
|[[File:Mark2-acrylic-FrameTopBarLCD.PNG|frameless|250px]]
|-
|Control
|LCD Controller (20x4) + SD Card Reader for RAMPS
|1
|-
|Control
|Smart Controller Cables
|2
|-
|Control
|RAMPS Smart Controller Adaptor
|1
|-
|Control
|Machined Metal Knob
|1
|-
|Fixings
|{{Bolt|M3|20}}
|4
|-
|Fixings
|{{Washer}}
|4
|-
|Fixings
|{{Nut|M3}}
|4
|-
|}
|}

Latest revision as of 17:48, 29 March 2016


Mark2 3D Printer


Main BOM

These are the primary components in every kit. Extruder options (x-carriage, extruder, HotEnd) are not included in this list, and are listed separately below.

Category Part Quantity
Control RAMPS Board 1
Control A4988 Stepper Driver 5
Control Arduino Mega 2560 1
Control MightyFan Board 1
Control Endstop with cable 2
Control IR Z Probe with cable 1
Control LCD Controller (20x4) + SD Card Reader 1
Control LCD Controller Cables 2
Control LCD Controller Adaptor 1
Control Machined Metal Knob 1
Electronics 12V 30A PSU 1
Electronics IEC13 Mains Lead (default Australian) 1
Electronics IEC320 Mains Socket 1
Electronics NEMA17 Stepper Motor (34mm) 4
Wiring USB-A Cable 1.5m 1
Wiring Mains Wiring Harness 1
Wiring 12V Wiring Harness 1
Wiring Spiral Wire Wrap 2 metres
Wiring Cable Ties Pack
Wiring Cable Tie Mounts 10
Rods Smooth-rod 8x350mm 7
Rods Leadscrew TR8x300mm 2
Hardware F624ZZ Bearing 4
Hardware LM8UU Bearing 12 (2 spares)
Hardware GT2 Belt 2 metres
Hardware GT2 Pulley 2
Hardware Spring 4
Hardware 5mm to 8mm Flex Coupler 2
Print Bed MK3 Aluminium Heated Bed + Wire, Thermistor 1
Print Bed 200x214mm Glass Plate 1
Print Bed Wooden Insulator 1
Print Bed A4 Black Paper 1
Fixings M3x10mm Bolt 5
Fixings M3x15mm Bolt 30
Fixings M3x20mm Bolt 85
Fixings M3x20mm Countersunk Bolt 8
Fixings M3x30mm Bolt 4
Fixings M3 Hex Nut 125
Fixings M3 Spring Washer 125
Fixings M3 Nyloc Nut 5
Fixings M3 Plastic Spacer 25
Fixings M4x20mm Bolt 5
Fixings M4 Hex Nut 5
Fixings Binder Clip (25mm) 4
Fixings Hex Keys - 2.0mm, 2.5mm and 3.0mm 1 set
Misc Filament Sample 1
Acrylic Acrylic Frame (see separate BOM) 1
Printed Printed Frame Parts (see separate BOM) 1 Set

Acrylic BOM

Part Acrylic Thickness (mm) Quantity Image
Side Panel (Left) 10 1 Mark2-acrylic-SidePanelLeft.PNG
Side Panel (Right) 10 1 Mark2-acrylic-SidePanelRight.PNG
Y Front Panel 10 1 Mark2-acrylic-YAxisFront.PNG
Y Rear Panel 10 1 Mark2-acrylic-YAxisRear.PNG
Horizontal Brace 10 1 Mark2-acrylic-HorizontalBrace.PNG
Y Motor Bracket 10 1 Mark2-acrylic-YMotorBracket.PNG
Z Motor Bracket 10 2 Mark2-acrylic-ZMotorBracket.PNG
Z Motor Brace 10 4 Mark2-acrylic-ZMotorBrace.PNG
Z Smoothrod Cap 10 2 Mark2-acrylic-ZSmoothrodCap.PNG
Top Bar (Front) 10 1 Mark2-acrylic-FrameTopBarLCD.PNG
Top Bar (Rear) 10 1 Mark2-acrylic-FrameTopBarRear.PNG
Bed Support Plate 4.5 1 Mark2-acrylic-BedSupportPlate.PNG
Smoothrod Cap 4.5 6 Mark2-acrylic-SmoothrodCap.PNG
Y Endstop Bracket 4.5 1 Mark2-acrylic-YEndstopBracket.PNG

Printed BOM

Part Quantity Image
X-Motor 1 Mark2-printed-x-motor.PNG
X-Idler 1 Mark2-printed-x-idler.PNG
X-Idler-Tensioner 1 Mark2-printed-x-idler-tensioner.PNG
Y-Idler 1 Mark2-printed-y-idler.PNG
Y-Belt-Clamp 2 Mark2-printed-y-belt-clamp.PNG
Belt-Screw-Cap 1 Mark2-printed-belt-screw-cap.PNG
Spool-Rod-Adaptor 2 Mark2-printed-spool-rod-adaptor.PNG
Fan-Duct 1 Mark2-printed-fan-duct.PNG
Fan-Mount 1 Mark2-printed-fan-mount.PNG
X-Belt-Clip 2 (Mirrored) Mark2-printed-x-belt-clip.PNG

Single Extruder BOM

Category Part Quantity
Extruder Metal Extruder Base 1
Extruder Metal Extruder Idler 1
Extruder MK7 Filament Gear 1
Extruder Bearing 1
Electronics 50mm 12V Blower Fan 1
Electronics NEMA 17 Stepper Motor 1
Electronics Fan Connector and Crimp Ferrules 1 Set
Fixings M3x10mm Bolt 3
Fixings M3x30mm Bolt 12
Fixings Washer 1
Fixings Imperial 6/32 x 1.5" Bolt 1
Fixings Imperial 6/32 Nut 1
Fixings Spring 1
Fixings Printed Circlip 1

Acrylic

Part Acrylic Thickness (mm) Quantity Image
X Carriage Front 4.5 1 Mark2-acrylic-XCarriageFront.png
X Carriage Rear 4.5 1 Mark2-acrylic-XCarriageRear.png
X Carriage Brace 4.5 2 Mark2-acrylic-XCarriageBrace.png
X Carriage Mount Plate 4.5 1 Mark2-acrylic-XCarriageMountPlate.png

Dual Extruder BOM

Category Part Quantity
Fixings M3x10mm Bolt 5
Fixings M3x30mm Bolt 6

Acrylic

Part Acrylic Thickness (mm) Quantity Image
Retrieved from "https://wiki.aus3d.com.au/index.php?title=Mark2_BOM&oldid=705"